Calculating PCB Fabrication Costs (Watch Out!)

We get this question a lot: How much per square inch for a 4-layer board? (or double sided, or 6 layers … same question).  I won’t hold you to it, I promise. Right….

We understand that it is difficult to provide the boss with a project cost roll up if you do not have the board cost estimate. If you do a lot of designs you may have a feel for it or you may refer to a similar board cost from a past project. This actually can be very effective.

I have even seen online cost calculators that presume to give an accurate number.  Knowing what I know about PCB pricing, however, I can say that it just ain’t so.

Here is why calculating PCB cost is tricky and dangerous ground.

The biggest cost drivers for a bare board are:

  1. Who are you? Are you a stranger or newcomer, or do you have established relationships with board vendors? Most of us manufacturers figure the total dollar volume somewhere into the pricing equation.
  1. Board size. Square area of the board, plus the square inches of material remaining on the panel after routing your unique board shape. (You are charged by the processed panel).
  1. Production volumes in the 10 boards to 1000 boards range will have a very steep cost curve. The curve flattens out as the order rises above 1000 and gets very unpredictable at 100,000. Who you are begins to make a big difference at this level, along with your negotiating skills.

All manufacturers have a floor or minimum and it is best to ask how many boards you can get for the minimum charge. Some of the internet guys will sell one or five at a very low seemingly low cost, but your boards will have to fit perfectly into their narrow technical profile.

  1. Delivery days requirement. This can be very steep cost curve in the one to 10 day requirement range. After 10 days, little influence unless the volumes are large. We turn boards from our China factory in 10 working days and small expedite fees for five days. (Yes, we turn boards from China in five days.)
  1. Manufactured location. USA, China, Europe, Taiwan. This is usually a preferential decision, but clearly, China has the edge, followed by Taiwan. Differences can be great.
  1. Number of layers. No surprise here. From double-sided to four layers, costs will go up about 60%. From four layer to six layer add another 50%. For six to eight layers add 30%. Keep in mind that each added layer is the equivalent of a double-sided board added to the stack.  Also, remember that high-layer-count boards are often accompanied by tough technical requirements and buried vias.
  1. Technology stretching requirements, like exotic materials, super small geometries, buried vias, etc. This can be steep or moderate depending upon the manufacturer and the difficulty. Tg requirements will have a moderate impact.
  1. Surface finish, like HASL, ENIG, tin, OSP. If you can handle OSP, it is the lowest cost, followed by HASL, then ENIG. ENIG is so common these days that for low volumes, it can be as low cost as HASL.

Not the following:

  1. Number of drill hits; however, the total number drill tools used can drive costs up. Ten tools is the preferred maximum and usually can do the job.
  2. Presence or absence of a silk screen legend. (Minor influence.)
  3. Always insist on testing at no charge.

So, now think about putting all of this into an algorithm and coming up with a defensible, unchangeable answer. That is a dangerous guessing game.

My best advice is this: Get preliminary Gerbers to your preferred vendors and tell them they are preliminary. If the effort is conceptual, provide a simple description answering the cost drivers above and email your proposed or preferred vendors for a quote. (To make it easy for you, we offer a template. Go to precisionpcbs.com/pcb-manufacturing and click on the “Fab Drawing Template.”)

One thought on “Calculating PCB Fabrication Costs (Watch Out!)

  1. Hello Tom! Great post you have shared. I liked it . No doubt the post is small but very informative one. To me, I am PCB repair tool manufacture who made tool kits and materials that helps you in fast repair and modification of lands, traces, contact fingers, SMT pads, plated hole connections and PCB base board material. Anyway thanks for sharing the post.

Comments are closed.