Soldering 101: The Simplicity of Soldering – The Complexity of Solder Paste

Folks,

Soldering copper to copper with a tin-based solder, such as tin-lead eutectic solder or a common lead-free solder like SAC 305, requires only the liquid solder and copper to form the tin-copper intermetallic bond. This simplicity, with one small catch, was brought home to me by some colleagues at Speedline Technologies. They took a PWB with through-hole components mounted and ran it through a wave-soldering machine without using any flux. The result was comical. The PWB weighed about 10 pounds as it had huge solder ice cycles hanging off of it. Oxides that form on the copper created this mess. Running the board though again with a nitrogen blanket produced a beautifully wave-soldered board that could be ready to ship. So in reality, either a flux or nitrogen, preferably both are needed for successful wave soldering in addition to the solder and copper; however, it is still relatively simple.

Have sympathy for the solder scientists of the late 1970s and early 1980s. SMT was an emerging technology and the world wanted to buy solder paste; however, the only experience many solder scientists had was with wave soldering. In wave soldering, the flux’s main job is to remove the oxides from the PWB pads and components. The solder is in a molten state and its oxidation is not a main concern. In the soldering process, the solder only touches the board for a few seconds and the board only experiences the high temperatures during this brief period.

I imagine some early solder pastes consisted of solder powder with fluxes similar to those used in wave soldering. If so, they probably didn’t work too well. Consider the dramatic differences that solder paste experiences as compared to solder in wave soldering. The “flux” in solder paste has to remove oxides from the PWB pads, component leads, and solder particles, but it also has to protect all of these surfaces from re-oxidation for several minutes while in the reflow oven. To achieve this protection, the “flux” has to contain materials that act as an oxygen barrier. The most common materials used in no-clean solder pastes are rosins/resins. Rosins, or resins which are modified or synthetic rosins, are generally medium to high molecular weight organic compounds of 80-90% abietic acid. They are typically found in coniferous trees. Rosins/resins are tacky in nature, and provide some fluxing activity and oxidation resistance during the reflow process.

The reason I wrote “flux” in the above paragraph is that what most people call the flux in solder paste is a complex combination of materials. These “fluxes” will consist of:

    • Rosins/resins: for oxygen barrier and some fluxing activity
    • Rheological additives: to give the best printing properties, e.g., good response-to-pause, good transfer efficiency, excellent slump resistance, good tack, etc
    • Solvents: to dissolve the other materials
    • Activators: to perform the main fluxing action (removing oxides)

      Figure. Solder pastes are one of the most highly engineered materials.

Modern solder pastes must have good oxygen barrier capability. In most reflow profiles, the solder paste is at temperatures above 150ºC for more than several minutes. During this time, an oxygen barrier is needed to protect both the solder particles and the surfaces of the pads and leads.

A common example of an insufficient solder barrier is the graping defect or its relative, the head-in-pillow defect. If you are experiencing one of these defects, a solder paste with better oxygen barrier properties is bound to help.

Before reflow, the solder paste must print well, possess good response-to-pause, not shear thin, resist cold slump, and have good “tack” to support the components after placement. During reflow, in addition to the oxygen barrier challenge, the solder paste must not exhibit hot slump, should “Avoid the Void,” not create the “head-in-pillow” (HIP) defect, work with all common PWP pad finishes, and produce reliable solder joints in thermal cycling, drop shock, and vibration environments. Whew! What a complex challenge.

As a result I would argue that solder paste is a candidate to be the most highly engineered material in the world… and it certainly is NOT a commodity.

Cheers,
Dr. Ron